Autre

FAYMONVILLE PREFAMAX 3HH-18-9.50-22.5-2.55-HD

Technical data Prefa-3HH-18-9.50-22.5-2.55-HD
Speed : 80 km/h
Total weight* : 45000 kg
fifth wheel load : 18000 kg
Axle load : 27000 kg
Tare weight (basic version) ± 3% : 9595 kg
Payload approx. : 35405 kg
Gooseneck length approx. : 3 500 mm
Rear kingpin steering radius approx. : 2 300/2 000 mm
Semi-mounted height loaded approx. : 1150-1300 mm
Height compensation front lift arm approx. : -280/+250 mm
Loading area length approx. : 9 500 mm
Loading width approx. : 1 560 mm
Suspension travel (with hydraulic compensation) approx. : -280/+230 mm
Wheelbase kingpin to center of axle unit approx. : 8 000 mm
Axle spacing : 2x 1 405 mm
Basic vehicle width approx. : 2 550 mm
Total towing length* approx. : 16500 mm
With length SZM front to center of fifth wheel approx. : 4500 mm
*Total weight depends on the fifth wheel load.
Special permit required Yes
If exceeding the
country-specific legislation :
Technical description
Gooseneck: Gooseneck designed as a loading surface with checker plate covering.
Hydraulic lifting arm approx. -280/+250 mm can be raised and
lowerable.
Two kingpin positions at 2,000 mm and 2,300 mm.
For SZM: 4 x 2, 6 x 2 or 6 x 4
Loading chute: Loading chute, length approx. 9,500 mm, with angle profiles attached at the bottom
angle profiles for holding the loading pallets.
(Distance from kingpin to center of axle unit approx. 8,000 mm)
Axles and suspension : BPW stub axles, with drum brakes and independent wheel suspension
independent wheel suspension, hydraulic axle compensation with lifting and
lowering device.
Each axle can be lifted individually.
Anti-lowering device on the axles for
suspension hose burst, designed for pallet height max.
150 mm.
Axle tool.
Brake system: EBS brake system from WABCO in accordance with
EU regulations.
WITHOUT connecting cable to the tractor unit.
Tires: 385/65 R 22.5 (M+S)
Make of our choice
Lighting system 24-volt lighting system in "ASPÖCK-NORDIK" (ASS 3)
Designed in accordance with EU regulations.
Side lighting in LED
Metallization: Part HRM metallization (High Resistance Metallization)
The entire steel structure is shot-peened, then the defined visible
defined visible surfaces with ZINACOR 850 (zinc 85% - aluminum
aluminum 15%).
Painting 6-K final treatment:
Complete steel construction after welding
shot-blasted.
1 coat of zinc-based primer, 1 coat of adhesion primer.
Final coating with 2 coats of 2-component paint (acrylic) in a single color in
RAL colors of your choice, then sealing of the cavities with special
cavities with special wax.
Rims in silver.
Multicolor and special paintwork at an extra charge.
Steel construction: Steel construction made of high-strength fine-grained steels.
Steel grades:
S355J2+N/S355MC (yield strength 355MPa)
Cwpbz2Qe
S690QL/S700MC (yield strength 690MPa)
Welder DIN-EN 287-1 tested.
MAG welding process according to EN ISO 4063.
Shielding gas M21 according to EN ISO 14175
Accessories included
i3 pairs of recessed lashing rings on the gooseneck (LC 5,000 daN).
Steel tool box with lid, recessed in the rear area of the gooseneck, approx.
970 x 660 x 240 mm (L x W x D).
i
i2" kingpin
i4 Restraint shoes with bracket in front of the front wall.
Lighting for operating the gooseneck, suspension and hydraulic tensioning with on/off switch.
tensioning with on/off switch.
i
iMechanical downpipe supports for approx. 48,000 kg support load.
Access ladder on the right in the direction of travel, with 2 plug-in retaining brackets.
The ladder can optionally be fitted by the customer

L'annonce a été traduite automatiquement et des erreurs de traduction peuvent apparaître.